WEBVTT

00:00:00.256 --> 00:00:02.219
Hi, I'm Steve Smith with Camper Van

00:00:02.219 --> 00:00:05.291
Freedom. My passenger-side roof camera needed a

00:00:05.291 --> 00:00:07.339
custom mounting frame. I made it from

00:00:07.339 --> 00:00:10.134
aluminum extrusion and drilled connecting brackets,

00:00:10.155 --> 00:00:12.133
with the camera above a small light.

00:00:12.190 --> 00:00:14.900
Two recorded work sessions covered fourteen hours,

00:00:15.006 --> 00:00:17.033
including tool setup and parts for additional

00:00:17.096 --> 00:00:19.827
mounts. Both entries ended with the roof

00:00:19.827 --> 00:00:21.449
project still in progress.

00:00:21.662 --> 00:00:24.424
The first session started with angle-aluminum stock.

00:00:24.540 --> 00:00:26.418
I made small connecting brackets,

00:00:26.503 --> 00:00:28.359
drilled their holes and joined the extrusion

00:00:28.380 --> 00:00:30.983
pieces. The loose bracket photograph shows the

00:00:30.983 --> 00:00:33.117
two faces of the angle before assembly.

00:00:33.201 --> 00:00:35.015
The close-up shows a connecting piece inside

00:00:35.079 --> 00:00:37.365
an extrusion corner. Looking at those views

00:00:37.365 --> 00:00:39.883
together makes the relationship between the stock,

00:00:39.967 --> 00:00:42.037
the holes and the finished joint easier

00:00:42.101 --> 00:00:44.953
to follow. The small hardware took time.

00:00:45.073 --> 00:00:48.230
My diary specifically records positioning the T-nuts

00:00:48.230 --> 00:00:50.258
and getting the screws started in them.

00:00:50.321 --> 00:00:52.284
A rectangular frame may look simple in

00:00:52.284 --> 00:00:54.545
a wide photograph, but each corner still

00:00:54.545 --> 00:00:57.542
depends on engaging those individual fastening pieces.

00:00:57.764 --> 00:00:59.983
The hardware photograph belongs beside the joint

00:00:59.983 --> 00:01:02.351
picture, because it records the small parts

00:01:02.457 --> 00:01:04.293
involved in that fitting stage.

00:01:04.420 --> 00:01:06.802
Bolt length was another problem I recorded.

00:01:06.879 --> 00:01:09.034
I planned to buy shorter quarter-twenty bolts

00:01:09.055 --> 00:01:10.207
so I would not have to grind

00:01:10.207 --> 00:01:12.000
every bolt down to fit.

00:01:12.169 --> 00:01:13.620
That was a purchasing plan at the

00:01:13.620 --> 00:01:14.811
end of the first session.

00:01:15.019 --> 00:01:17.024
Keeping a proposed change separate from the

00:01:17.024 --> 00:01:19.499
pieces already fitted helps explain why the

00:01:19.499 --> 00:01:21.675
assembly was not finished when that photograph

00:01:21.675 --> 00:01:23.979
was taken. The next session began with

00:01:23.979 --> 00:01:26.318
unboxing and assembling my drill press.

00:01:26.394 --> 00:01:28.058
I then drilled larger holes in the

00:01:28.058 --> 00:01:30.192
exterior extrusion corner brackets.

00:01:30.319 --> 00:01:32.538
That setup work belongs within the fourteen-hour

00:01:32.538 --> 00:01:34.714
record, rather than treating all the time

00:01:34.714 --> 00:01:36.368
as camera attachment alone.

00:01:36.527 --> 00:01:37.892
The rest of the session included more

00:01:37.892 --> 00:01:40.409
measuring, cutting and drilling for the remaining

00:01:40.409 --> 00:01:42.842
mounts, along with cutting their extrusion.

00:01:43.055 --> 00:01:45.401
The existing camera mount also received more

00:01:45.401 --> 00:01:47.905
attachment work. I added corner brackets and

00:01:47.905 --> 00:01:49.569
made a separate bracket for the camera's

00:01:49.569 --> 00:01:51.873
front mounting hole. The camera base and

00:01:51.873 --> 00:01:54.177
the custom extrusion frame were different parts

00:01:54.177 --> 00:01:56.292
of the job. My fitting photographs show

00:01:56.292 --> 00:01:58.554
the earlier assembly, while the following day's

00:01:58.554 --> 00:02:01.349
written steps record those later bracket additions.

00:02:01.711 --> 00:02:03.375
The cable was still visible around the

00:02:03.375 --> 00:02:05.751
camera during fitting. More conduit and wire

00:02:05.751 --> 00:02:07.139
routing were planned next.

00:02:07.330 --> 00:02:08.312
For a fitting record,

00:02:08.354 --> 00:02:10.061
I would keep one row per joint,

00:02:10.061 --> 00:02:11.085
with the stock shape,

00:02:11.085 --> 00:02:14.179
hole position, hardware, actual bolt length,

00:02:14.199 --> 00:02:16.366
photograph and next change together.

00:02:16.483 --> 00:02:18.232
That separates a loose bracket,

00:02:18.232 --> 00:02:20.792
an assembled corner and a camera attachment

00:02:20.792 --> 00:02:22.755
instead of treating the whole roof as

00:02:22.755 --> 00:02:25.337
one completed item. Thanks for watching.

00:02:25.357 --> 00:02:27.675
I'm Steve Smith with Camper Van Freedom.

00:02:27.773 --> 00:02:29.778
My camera-bracket project was a sequence of

00:02:29.778 --> 00:02:31.763
small connections: angle stock,

00:02:31.783 --> 00:02:34.813
drilled holes, T-nuts, bolt lengths and another

00:02:34.813 --> 00:02:36.342
attachment at the camera base.

00:02:36.505 --> 00:02:38.681
The full guide, original photographs,

00:02:38.681 --> 00:02:41.113
diary entries and blank fitting record are

00:02:41.113 --> 00:02:43.346
linked below. Until next time.
