WEBVTT

00:00:00.256 --> 00:00:02.219
Hi, I'm Steve Smith with Camper Van

00:00:02.219 --> 00:00:04.779
Freedom. This is the storage-bin drawer I

00:00:04.779 --> 00:00:06.999
developed during my roof-storage project.

00:00:07.128 --> 00:00:08.749
I started with a SketchUp layout,

00:00:08.749 --> 00:00:10.413
laid out timber on the patio to

00:00:10.413 --> 00:00:11.864
represent the roof dimensions,

00:00:11.864 --> 00:00:13.784
and worked through the drawer and cabinet

00:00:13.784 --> 00:00:15.544
frame with the bins in place.

00:00:15.724 --> 00:00:17.260
The useful lesson was to keep the

00:00:17.260 --> 00:00:19.650
bin, the drawer and the cabinet as

00:00:19.650 --> 00:00:21.464
three separate parts of the plan.

00:00:21.612 --> 00:00:22.978
The bin is the container I need

00:00:22.978 --> 00:00:25.659
to reach. The drawer carries the containers.

00:00:25.908 --> 00:00:27.956
The cabinet surrounds the drawer and provides

00:00:27.956 --> 00:00:29.194
room for it to move.

00:00:29.321 --> 00:00:30.666
Their dimensions are related,

00:00:30.686 --> 00:00:32.180
but they are not interchangeable.

00:00:32.222 --> 00:00:34.313
A container's lid and handles can take

00:00:34.313 --> 00:00:36.098
up more space than its base.

00:00:36.304 --> 00:00:39.333
The drawer's frame, base and lining then

00:00:39.333 --> 00:00:40.848
take up space of their own.

00:00:40.997 --> 00:00:42.789
My patio mockup gave the layout a

00:00:42.789 --> 00:00:45.670
physical reference. After designing the storage system

00:00:45.690 --> 00:00:48.165
in SketchUp, I cut timber to simulate

00:00:48.165 --> 00:00:50.320
the roof dimensions. I could arrange the

00:00:50.320 --> 00:00:52.496
frame and containers within that space and

00:00:52.496 --> 00:00:54.160
see how the pieces related to one

00:00:54.160 --> 00:00:56.592
another. The photographs show the construction and

00:00:56.592 --> 00:00:57.809
fit stage I reached,

00:00:57.829 --> 00:00:59.621
rather than a finished installation on the

00:00:59.621 --> 00:01:02.332
van. My diary records the drawer's total

00:01:02.332 --> 00:01:05.384
dimensions as twenty-nine and three-quarter inches wide,

00:01:05.490 --> 00:01:07.794
nineteen and three-sixteenths inches deep,

00:01:07.794 --> 00:01:09.925
and three and seven-eighths inches high.

00:01:10.049 --> 00:01:12.310
The separate cabinet frame was thirty-four inches

00:01:12.310 --> 00:01:14.614
wide, twenty inches deep and thirty-six inches

00:01:14.614 --> 00:01:17.111
high, intended for two rows of drawers.

00:01:17.217 --> 00:01:19.330
Those are the recorded overall dimensions.

00:01:19.393 --> 00:01:21.774
Clear inside space needs its own measurements.

00:01:21.978 --> 00:01:23.344
I cut the drawer timber,

00:01:23.385 --> 00:01:25.177
drilled the pieces and screwed them into

00:01:25.177 --> 00:01:28.633
a rectangular frame. Galvanized right-angle brackets went

00:01:28.633 --> 00:01:30.724
inside the corners. I then marked the

00:01:30.724 --> 00:01:32.304
base panel for the screws,

00:01:32.388 --> 00:01:33.924
drilled it and fastened it to the

00:01:33.924 --> 00:01:36.286
frame. Keeping the stages separate made the

00:01:36.286 --> 00:01:38.376
connections visible before the lining covered the

00:01:38.376 --> 00:01:39.934
inside. For the lining,

00:01:39.955 --> 00:01:41.872
I cut the rubber mat with scissors.

00:01:42.038 --> 00:01:42.977
I cleaned the wood,

00:01:42.977 --> 00:01:45.665
applied spray adhesive in sections and pressed

00:01:45.665 --> 00:01:47.607
the material into place with a roller.

00:01:47.670 --> 00:01:49.825
The base and sides used separate pieces.

00:01:50.017 --> 00:01:52.065
Screws and flat washers also held the

00:01:52.065 --> 00:01:53.593
mat to the timber and base.

00:01:53.754 --> 00:01:55.269
My aim was to put rubber between

00:01:55.375 --> 00:01:57.317
the containers and drawer to reduce noise

00:01:57.338 --> 00:02:00.133
and vibration. The finished inside space changes

00:02:00.197 --> 00:02:01.605
when that lining goes in.

00:02:01.733 --> 00:02:03.482
The next stage connected the drawer and

00:02:03.482 --> 00:02:05.777
taller cabinet frame with drawer slides.

00:02:05.938 --> 00:02:08.541
The extended-drawer photograph shows the bins brought

00:02:08.541 --> 00:02:09.651
out from the frame.

00:02:09.778 --> 00:02:11.399
Fit means more than placing a bin

00:02:11.399 --> 00:02:13.106
in a tray. I also need room

00:02:13.106 --> 00:02:14.258
to reach the handles,

00:02:14.258 --> 00:02:16.464
remove a lid and lift the container.

00:02:16.578 --> 00:02:18.668
The space above the bin matters alongside

00:02:18.668 --> 00:02:20.056
the drawer's forward travel.

00:02:20.204 --> 00:02:22.317
The HOMZ bins appear in my materials

00:02:22.380 --> 00:02:23.547
list for this project.

00:02:23.731 --> 00:02:26.035
The guide also shows Rubbermaid and Sterilite

00:02:26.035 --> 00:02:28.851
container alternatives for comparison; those are not

00:02:28.851 --> 00:02:30.429
additional bins I am claiming to have

00:02:30.429 --> 00:02:33.174
used. Whatever container is being planned around,

00:02:33.195 --> 00:02:35.137
its actual footprint, lid,

00:02:35.157 --> 00:02:37.504
handles and removal movement belong in the

00:02:37.504 --> 00:02:40.439
same fit record. This diary entry records

00:02:40.439 --> 00:02:42.231
twelve hours of work and ends with

00:02:42.231 --> 00:02:44.707
a plan to continue the roof-storage project.

00:02:44.962 --> 00:02:47.735
The mockup, frame and lined drawer preserve

00:02:47.735 --> 00:02:48.952
that stage of the build.

00:02:49.058 --> 00:02:51.078
Thanks for watching. I'm Steve Smith with

00:02:51.078 --> 00:02:53.297
Camper Van Freedom. My full guide includes

00:02:53.297 --> 00:02:56.028
the original photographs, recorded dimensions and a

00:02:56.028 --> 00:02:59.335
downloadable bin, drawer and cabinet fit worksheet.

00:02:59.356 --> 00:03:00.402
They are linked below.

00:03:00.550 --> 00:03:01.540
Until next time.
