Watch the Ford Transit camper van conversion take shape, then open the build notes for the steps, photos, tools and materials behind each project.
Vanguard VGRBG-1116-0830SS Rear Bumper Guard — Assessment — Portrait
The chrome rear guard began as a plan for a black bedliner finish. My recorded bracket attempt ended with holes that did not line up, an instruction-diagram comparison and a possible return.
Vanguard VGRBG-1116-0830SS Rear Bumper Guard: My Bracket Assembly Problem — Portrait
I could not squeeze the connection together in the arrangement I was trying. I compared the parts with the diagram and considered returning the guard. The recording stops at that point.
Vanguard VGRBG-1116-0830SS Rear Bumper Guard Project
See The Rear-Guard Purchase Record And Options
Original footage and voice by Steven Smith.
Watch The Full Film In Portrait — 3:07
This independently framed upright version follows the complete introduction, assembly attempt, close-up and final assessment.
Read A Text Account Of The Video
I introduce the chrome Vanguard rear bumper guard and the supplied mounting hardware, with a plan to coat it black. I attempt to join the brackets and guard, show the connection close to the camera when the holes do not line up, compare the instruction diagram and consider a return. This is the rear-guard assembly attempt; the black front grille guard is covered in its own project.
Black Horse Spartan 17FT20MA Grille Guard: My Transit Installation — Landscape
I start underneath my 2023 Ford Transit 250 high-roof extended, removing the splash guard and dealing with a broken driver-side clip. The film follows the exposed mounts, center support, alignment and tightening, then shows the center section before the outer headlamp wings and the finished front.
Tires and Wheels
Short project clips hosted here on Camper Van Freedom.
Method MR701: the Matte-Black Choice
I introduce the matte-black wheels before the swap. This short clip follows the shop stage and the installed look.
The Installed Result: a Closer Look
See the installed wheels and tires on my Transit. I walk around the result and show the wheel-and-tire details.
Black RAPTOR: the Daylight Result
My final walkaround shows the black lower trim, wheel arches, bumper and hood after masking removal. This comes after the uneven sprayed sheen and the roller correction that made the sides glossier.
Full RAPTOR film — 4:42Preparation — 0:36Roller correction — 1:03Project context in the build diary
Camper Van Conversion Videos

Top Secrets for Safely Wiring Your Roof

Roof Wiring and Devices Project Day 7 Van Conversion: Electrical Secrets Exposed

Ultimate Camper Van Conversion Tips with Steve
Planning A Camper Van Conversion: Project Management And Build Order

Quick Fix for Aluminum Extrusion Damage: Drive-Thru Disaster

Camper Van Build Roof Wiring and Devices Project Day 6: Roof Wire Update

Exciting Camper Van Progress: Roof Wiring and Devices Project Day 5 Roof Wiring

Roof Wiring and Devices Project Day 4: Van Build Update - LED Lights & Camera Mounts on Roof

Roof Wiring and Devices Project Day 3: Enhancing Camper Van Security with Camera Mounts

Roof Wiring and Devices Project Day 2 of Camper Van Build: Roof Security Cameras

Camper Van Build: Roof Wiring and Devices Project Day 1 - Roof LED Lights and Wiring

Secrets of Thriving in Van Life Revealed by Can'T Hurt Me

Camper Van Build Diary Light Bar Mounting - Installing 54" LED Light Bar

Diesel Heater Project Day 4 Diesel Heater Install: Unforgettable Finish

Top Tips for Selecting Your Ideal Van Life Vehicle

Camper Van Build Diary: Diesel Heater Project Day 3 - Installing Diesel Heater - Day 3

Camper Van Build Diary - Diesel Heater Project Day 2 - Installing Diesel Heater Day 2

Camper Van Build Diary Diesel Heater Project Day 1 - Preparation for Installing Diesel Heater Under Passenger Seat

Where to Work on a Camper Van Without a Garage

Camper Van Conversion Build Diary - Floor Preparation for Sound Deadening - Preparing Floor for Kilmat Sound Deadening Mats
Floor Preparation for Sound Deadening · Interior Preparation

Camper Van Conversion Diary: Interior Preparation - Installing Interior Features and Planning for the Future
Five Exterior Projects: My Films and Build Notes
My Transit exterior changed through several separate jobs. These films let me follow the wheels, black coating, passenger-side running board and two different guard projects without losing the differences between their outcomes. I use the full films for the wider story and the short clips when I want to return to a particular stage.
Choose a project below for the introduction, closer process views and result. The earlier videos elsewhere on this page remain available alongside these additional edits. My written project stories hold the original photographs, diary links and longer explanations.
Tires and Wheels: Follow the Change from Stock to Installed
My wheel-and-tire footage works best as a before-and-after story. The starting walkaround records the stock assemblies on the white Transit. The Method boxes then put a name to the matte-black wheels before the tire-shop photographs and installed walkaround show the change on the van. Those are different parts of the same project, rather than separate installation tutorials.
I like the packaging introduction beside the finished view because it connects the loose product to the whole van. The shop photographs add another useful comparison: the removed stock assemblies can be seen away from the vehicle, while the final footage shows the black wheels and BFGoodrich tires in their new setting. My recorded reaction is about seeing the changed appearance for myself.
Use the short before-and-after when you want the visual change quickly. The full film keeps the introduction and result together. The Method clip concentrates on the boxes and wheel introduction, and the installed walkaround lets you look around the finished van. The original project story retains the shop photographs and my longer written account.
Method Race Wheels MR701 Project
Watch Tires And Wheels Main
Method Race Wheels MR701 + BFGoodrich All-Terrain T/A KO2 Tires on My 2023 Ford Transit — Landscape
Read This Video’s Spoken Transcript
Hello everyone. This is Steve. It's a beautiful day here in December in Phoenix, Arizona. I'm about to take my 2023 Ford Transit into the shop to get the wheels and tires changed. So I'm going to make a video about the stock wheels and tires and then show you what I'm changing them to. So here she is. These are the stock wheels and tires on my 2023 Transit.
And that's how they look. And so here are the wheels I'm going to be replacing them with. These are Method Race Wheels, matte black. It's the MR701s. So they've put the new tires and wheels on, and it's definitely a much better look. I'm quite happy with it. So if I go up close, you can see the larger off-road tires, the more aggressive-looking tread and the wheels.
And it's definitely an overall better look. And it's definitely an overall better look. So yes, I'm very, very happy with it.
Stage Clip: Tires And Wheels 01 Before After
Method Race Wheels MR701 And BFGoodrich All-Terrain T/A KO2 Tires — Before After — Portrait
Read This Video’s Spoken Transcript
So here she is. These are the stock wheels and tires on my 2023 Transit. So they've put the new tires and wheels on, and it's definitely a much better look. I'm quite happy with it. So yes, I'm very, very happy with it.
Stage Clip: Tires And Wheels 02 Method MR701
Method Race Wheels MR701 And BFGoodrich All-Terrain T/A KO2 Tires — Method MR701 — Portrait
Read This Video’s Spoken Transcript
And so here are the wheels I'm going to be replacing them with. These are Method Race Wheels, matte black. It's the MR701s. So they've put the new tires and wheels on, and it's definitely a much better look. I'm quite happy with it. So if I go up close, you can see the larger off-road tires,
Stage Clip: Tires And Wheels 03 Installed Walkaround
Method Race Wheels MR701 And BFGoodrich All-Terrain T/A KO2 Tires — Installed Walkaround — Portrait
Read This Video’s Spoken Transcript
So they've put the new tires and wheels on, and it's definitely a much better look. I'm quite happy with it. So if I go up close, you can see the larger off-road tires, the more aggressive-looking tread and the wheels. And it's definitely an overall better look. And it's definitely an overall better look. So yes, I'm very, very happy with it.
Black RAPTOR: Preparation, Spraying and the Roller Correction
My black RAPTOR project developed in stages. At the beginning I was looking at gray trim and exposed white lower panels. Preparation then changed the van into a mixture of paper, tape and exposed coating areas. The useful comparison is not just white versus black: it is the prepared surface, the first sprayed appearance and the finish I changed with a roller.
The expanded portrait film adds the closer preparation and lower-trim spray work. I keep the aerosol hood preparation separate from that black spray-gun footage. Around the hood and bumper, the aerosol clips belong to the preparation sequence. The bottle-fed black spray-gun work in the added footage follows the lower trim and lower edge.
The correction is the turning point in my story. In daylight I could see different amounts of sheen along the sides. I went back over those sprayed surfaces with the roller and tray supplied with the kit. The resulting appearance was more even to me and also glossier than I had wanted. The daylight result and later follow-up give that tradeoff context.
U-POL RAPTOR Black Urethane Bedliner Kit Project
Watch RAPTOR Landscape
U-POL RAPTOR Black Urethane Bedliner Kit: My Transit Trim and Hood Project — Landscape
Read This Video’s Spoken Transcript
Hi everyone, this is Steve with Project Freedom. I'm going to be working on my van here today doing RAPTOR spray on the plastic trim as well as the wheel wells in some of the bottom part of the van. So I'll show you what I'm going to do here. So basically I'm going to do it from there down to the bottom so I'm going to cover this white part here with the RAPTOR spray as well which takes a little bit different preparation because we have plastic molding and then we have the paint there.
I'm going to do the same with the wheel well up front here. I'm going to do the hood with the RAPTOR spray and then the front bumper, and then the front bumper, So the steps I've taken thus far have been that I washed everything with soap and water first then I degreased everything then I sanded everything then I degreased everything again then I used a tack cloth which is like a sticky I've never used it before but if I got it if I got it from Home Depot it's a sticky cloth that gets all the little dust and specks off and then that's where I am now
So I basically have my compressor here and as you can see the way it hooks up is the bottle actually thread up to and they provide a gun and a kit that I got and it's actually quite easy and spraying it's very easy everything is very black there after I did about two full coats of the RAPTOR spray all around So I'm looking at it today after I've done the bedliner yesterday and I'm not sure if you can see this.
I'm noticing a little bit of inconsistency in the evenness of the spray and you know probably from the sprayer but in some parts it has a little more sheen to it and others it's more flat. it looks a little uneven to me and so what I'm gonna do is get some more RAPTOR bedliner and then roll it on at least on the sides here because the sides are the most visible of course.
I'm going to show you my application over here. And I'm hoping that this will result in a bit more of an even application to the side here. And so let's take a look. I'm going to roll through that throughout and we'll see how it comes out. So I've finished rolling and everything is definitely much more even after the rolling. It's it's much more even.
The rolling, applying it that way makes the finish much glossier. It's like before it was quite matte. Now it's almost like a metallic finish. It's very shiny. I'm not sure if you can see this through the video, but the finish is very shiny. Not exactly what I wanted. I wanted more of a matte look, but that's alright. I'm still happy with it.
It looks good. So here we have the final product and I'm extremely happy with how it turned out. It was worth the three full days of work and get a little bit closer. As you can see it's pretty shiny but I like it a lot. The lines are very clean even though the tape got rained on and I'm extremely happy with the way it looks.
We'll go and take a look at the hood too. On this side how it turned out it looks very great and again very very happy with it.
Stage Clip: RAPTOR 01 Preparation Landscape
U-POL RAPTOR Black Urethane Bedliner Kit — Preparation — Landscape
Read This Video’s Spoken Transcript
So the steps I've taken thus far have been that I washed everything with soap and water first then I degreased everything then I sanded everything then I degreased everything again then I used a tack cloth which is like a sticky I've never used it before but if I got it if I got it from Home Depot it's a sticky cloth that gets all the little dust and specks off and then that's where I am now
Stage Clip: RAPTOR 01 Preparation Portrait
U-POL RAPTOR Black Urethane Bedliner Kit — Preparation — Portrait
Read This Video’s Spoken Transcript
So the steps I've taken thus far have been that I washed everything with soap and water first then I degreased everything then I sanded everything then I degreased everything again then I used a tack cloth which is like a sticky I've never used it before but if I got it if I got it from Home Depot it's a sticky cloth that gets all the little dust and specks off and then that's where I am now
Stage Clip: RAPTOR 02 Roller Correction Landscape
U-POL RAPTOR Black Urethane Bedliner Kit — Roller Correction — Landscape
Read This Video’s Spoken Transcript
I'm noticing a little bit of inconsistency in the evenness of the spray and you know probably from the sprayer but in some parts it has a little more sheen to it and others it's more flat. So I've finished rolling and everything is definitely much more even after the rolling. It's it's much more even. The rolling, applying it that way makes the finish much glossier. It's like before it was quite matte. Now it's almost like a metallic finish. It's very shiny. I'm not sure if you can see this through the video, but the finish is very shiny. Not exactly what I wanted. I wanted more of a matte look, but that's alright. I'm still happy with it. It looks good.
Stage Clip: RAPTOR 02 Roller Correction Portrait
U-POL RAPTOR Black Urethane Bedliner Kit — Roller Correction — Portrait
Read This Video’s Spoken Transcript
I'm noticing a little bit of inconsistency in the evenness of the spray and you know probably from the sprayer but in some parts it has a little more sheen to it and others it's more flat. So I've finished rolling and everything is definitely much more even after the rolling. It's it's much more even. The rolling, applying it that way makes the finish much glossier. It's like before it was quite matte. Now it's almost like a metallic finish. It's very shiny. I'm not sure if you can see this through the video, but the finish is very shiny. Not exactly what I wanted. I wanted more of a matte look, but that's alright. I'm still happy with it. It looks good.
Stage Clip: RAPTOR 03 Daylight Result Landscape
U-POL RAPTOR Black Urethane Bedliner Kit — Daylight Result — Landscape
Read This Video’s Spoken Transcript
So here we have the final product and I'm extremely happy with how it turned out. It was worth the three full days of work and get a little bit closer. As you can see it's pretty shiny but I like it a lot. The lines are very clean even though the tape got rained on and I'm extremely happy with the way it looks. We'll go and take a look at the hood too. On this side how it turned out it looks very great and again very very happy with it.
Stage Clip: RAPTOR 03 Daylight Result Portrait
U-POL RAPTOR Black Urethane Bedliner Kit — Daylight Result — Portrait
Read This Video’s Spoken Transcript
So here we have the final product and I'm extremely happy with how it turned out. It was worth the three full days of work and get a little bit closer. As you can see it's pretty shiny but I like it a lot. The lines are very clean even though the tape got rained on and I'm extremely happy with the way it looks. We'll go and take a look at the hood too. On this side how it turned out it looks very great and again very very happy with it.
The Expanded Portrait Film and Six Closer Views
The expanded 9:57 portrait film adds lower-trim preparation, hood and bumper preparation, aerosol hood preparation, two parts of the lower-trim black spray session and my finish assessment.
U-POL RAPTOR Black Urethane Bedliner Kit Project · U-POL RAPTOR Black Urethane Bedliner Kit Project · U-POL RAPTOR Black Urethane Bedliner Kit Project · U-POL RAPTOR Black Urethane Bedliner Kit Project · U-POL RAPTOR Black Urethane Bedliner Kit Project · U-POL RAPTOR Black Urethane Bedliner Kit Project · U-POL RAPTOR Black Urethane Bedliner Kit Project
Ramps and Side Runner Bars: the Passenger-Side Work
This film starts before the running board is attached. I introduce the ramps, then show the work area with the creeper, tools and board laid out. That setup matters to the story because it records the pieces around me before the closer views move underneath the passenger side.
The middle of the project is about the mounting area. I show loosening the lower trim clips, prepared holes and mounting points, and the bracket attached beneath the van. The closer mounting clip is the useful place to look at those connections; the wider film makes it easier to follow how the setup leads into that work.
The closing returns to a wider view of the passenger side with the board in place. I was happy with that result and explicitly said I still needed to do the driver side. That is where this project recording ends. I keep the completed passenger-side view beside the earlier setup rather than turning it into a claim that both sides were finished.
HD Ridez N-Series Running Boards Project
Watch Running Board Full Portrait
HD Ridez N-Series Running Boards: My Ford Transit Passenger-Side Installation — Portrait
Read This Video’s Spoken Transcript
Hey everyone, this is a review of RhinoRamps. I have four four of them here so that I can prop up all four wheels in my 2023 Ford Transit 250 and I'm going to be using them today to install some things in my van and giving a review. Now these are the RhinoRamps MAX. So, to install the running boards it wants me to loosen these plastic clips on the trim here underneath the passenger side of my Transit.
And so I'm going to go ahead and see if I can record myself doing that. It says don't take off the trim but just loosen it which is good because I bedlinered my trim. But it says I should just be able to stick a flathead in here. And then pull this down. It's a little difficult to do with one hand. That saying once I stick the flathead in there it should just kind of come down.
It appears like it is loosening up. It's almost like you have to pry it a little bit off. It definitely can get my fingers in that small space there. Interesting. So that's what you do. I'm going to have to try to do it with two hands here. So, I'm underneath the passenger side of the van and installing the running board here. And I'm just showing you how it's installed.
So, you have, this is a, this is a factory hole here. And then you have the bolt. This is being held by this plastic retainer. But also, there's something behind there that basically catches inside. And then I drill these two holes and we have these clips here. So, then I'm going to put this, I'll show you after I'm done, I'm going to put the bracket on there that's attached to the running board.
And then these are the factory studs and the bracket mounts on those. So, I'll show you all this when I'm done. So you can see here we got our bracket. These are the two factory studs. There's a washer and then a nut there and then I drilled those holes and you use these retainer clips. I clip onto the metal there right behind the plastic trim and there's a locking washer and a regular washer and a nut or in a bolt and so then you fasten that on to the chassis there.
And then this whole mounting bracket as you can see mounts to the running board. So that's how it attaches to the underside here. I'm on the passenger side. So here's the finished product on the passenger side with the running board. I'm very happy with the way it looks. And the finish on it actually matches the bed liner perfectly. Looks like they put on some bed liner themselves.
And so looks really nice. So one thing about this is it doesn't run all the way to the back tires because I have the extended version. But it still looks fine and it matches up with the the the doors really well where you would do it. So overall really happy with it. Still needs to do the driver side though.
Watch Running Board Full Landscape
HD Ridez N-Series Running Boards: My Ford Transit Passenger-Side Installation — Landscape
Read This Video’s Spoken Transcript
Hey everyone, this is a review of RhinoRamps. I have four four of them here so that I can prop up all four wheels in my 2023 Ford Transit 250 and I'm going to be using them today to install some things in my van and giving a review. Now these are the RhinoRamps MAX. So, to install the running boards it wants me to loosen these plastic clips on the trim here underneath the passenger side of my Transit.
And so I'm going to go ahead and see if I can record myself doing that. It says don't take off the trim but just loosen it which is good because I bedlinered my trim. But it says I should just be able to stick a flathead in here. And then pull this down. It's a little difficult to do with one hand. That saying once I stick the flathead in there it should just kind of come down.
It appears like it is loosening up. It's almost like you have to pry it a little bit off. It definitely can get my fingers in that small space there. Interesting. So that's what you do. I'm going to have to try to do it with two hands here. So, I'm underneath the passenger side of the van and installing the running board here. And I'm just showing you how it's installed.
So, you have, this is a, this is a factory hole here. And then you have the bolt. This is being held by this plastic retainer. But also, there's something behind there that basically catches inside. And then I drill these two holes and we have these clips here. So, then I'm going to put this, I'll show you after I'm done, I'm going to put the bracket on there that's attached to the running board.
And then these are the factory studs and the bracket mounts on those. So, I'll show you all this when I'm done. So you can see here we got our bracket. These are the two factory studs. There's a washer and then a nut there and then I drilled those holes and you use these retainer clips. I clip onto the metal there right behind the plastic trim and there's a locking washer and a regular washer and a nut or in a bolt and so then you fasten that on to the chassis there.
And then this whole mounting bracket as you can see mounts to the running board. So that's how it attaches to the underside here. I'm on the passenger side. So here's the finished product on the passenger side with the running board. I'm very happy with the way it looks. And the finish on it actually matches the bed liner perfectly. Looks like they put on some bed liner themselves.
And so looks really nice. So one thing about this is it doesn't run all the way to the back tires because I have the extended version. But it still looks fine and it matches up with the the the doors really well where you would do it. So overall really happy with it. Still needs to do the driver side though.
Stage Clip: Running Board Setup Portrait
HD Ridez N-Series Running Boards — Setup — Portrait
Read This Video’s Spoken Transcript
Hey everyone, this is a review of RhinoRamps. I have four four of them here so that I can prop up all four wheels in my 2023 Ford Transit 250 and I'm going to be using them today to install install some things in my van and giving a review. Now these are the RhinoRamps MAX.
Stage Clip: Running Board Mounting Portrait
HD Ridez N-Series Running Boards — Mounting — Portrait
Read This Video’s Spoken Transcript
So, to install the running boards it wants me to loosen these plastic clips on the trim here And then you have the bolt. This is being held by this plastic retainer. But also, there's something behind there that basically catches inside. So you can see here we got our bracket. These are the two factory studs. There's a washer And then this whole mounting bracket as you can see mounts to the running board. So that's how it attaches to the underside here. I'm on the passenger side.
Stage Clip: Running Board Result Portrait
HD Ridez N-Series Running Boards — Result — Portrait
Read This Video’s Spoken Transcript
So here's the finished product on the passenger side with the running board. I'm very happy with the way it looks. And the finish on it actually matches the bed liner perfectly. Looks like they put on some bed liner themselves. And so looks really nice. So one thing about this is it doesn't run all the way to the back tires because I have the extended version. But it still looks fine and it matches up with the the the doors really well where you would do it. So overall really happy with it. Still needs to do the driver side though.
Stage Clip: Running Board Setup Landscape
HD Ridez N-Series Running Boards — Setup — Landscape
Read This Video’s Spoken Transcript
Hey everyone, this is a review of RhinoRamps. I have four four of them here so that I can prop up all four wheels in my 2023 Ford Transit 250 and I'm going to be using them today to install install some things in my van and giving a review. Now these are the RhinoRamps MAX.
Stage Clip: Running Board Mounting Landscape
HD Ridez N-Series Running Boards — Mounting — Landscape
Read This Video’s Spoken Transcript
So, to install the running boards it wants me to loosen these plastic clips on the trim here And then you have the bolt. This is being held by this plastic retainer. But also, there's something behind there that basically catches inside. So you can see here we got our bracket. These are the two factory studs. There's a washer And then this whole mounting bracket as you can see mounts to the running board. So that's how it attaches to the underside here. I'm on the passenger side.
Stage Clip: Running Board Result Landscape
HD Ridez N-Series Running Boards — Result — Landscape
Read This Video’s Spoken Transcript
So here's the finished product on the passenger side with the running board. I'm very happy with the way it looks. And the finish on it actually matches the bed liner perfectly. Looks like they put on some bed liner themselves. And so looks really nice. So one thing about this is it doesn't run all the way to the back tires because I have the extended version. But it still looks fine and it matches up with the the the doors really well where you would do it. So overall really happy with it. Still needs to do the driver side though.
Front Grille Guard: from Exposed Mounts to the Completed Shape
My black front grille guard story starts beneath the front of the Transit. I remove the splash guard and encounter a broken clip on the driver side before showing the exposed mounting area. Those early views explain why the project film spends time underneath before the guard becomes the main subject.
The center support at the license-plate position is a useful detail to follow into the bracket stage. My recording discusses leaving connections loose for alignment before tightening. The photographs then show the center section in place before the outer headlamp wings, which makes the final shape easier to understand.
The transformation clip is a sequence of actual photographs. It is useful for comparing the center-only stage with the completed guard, while the preparation and mounting clips carry the closer process explanation. I keep this black front installation separate from my chrome rear-guard assembly attempt; the outcomes were different.
Black Horse Spartan 17FT20MA Grille Guard Project
Black Horse Spartan 17FT20MA Grille Guard Project · Black Horse Spartan 17FT20MA Grille Guard Project · Black Horse Spartan 17FT20MA Grille Guard Project
The full landscape installation film remains above on this video page. Follow the project story for the close preparation and mounting clips beside the original photographs.
Vanguard Rear Guard: the Bracket Attempt and My Assessment
The chrome rear guard began with a different plan from my black front installation. I bought the Vanguard guard and talked about coating it with black bedliner. The recorded work stops earlier, while I am trying to put the guard and brackets together.
The useful middle section is the bracket attempt itself. With the guard across my lap, I try the connections and look at holes that do not line up. I compare the parts with the instruction diagram and explain why I am considering returning it. The close assembly views and the final assessment belong together because the assessment follows the problem shown immediately before it.
This is a record of an unfinished attempt rather than a completed rear installation. The introduction clip explains the product and intended finish; the alignment clip follows the actual fitting problem; the assessment clip records where I left the decision. My separate front grille guard project reaches a completed appearance, so I keep the two stories clearly separated.
Vanguard VGRBG-1116-0830SS Rear Bumper Guard Project
Vanguard VGRBG-1116-0830SS Rear Bumper Guard Project · Vanguard VGRBG-1116-0830SS Rear Bumper Guard Project · Vanguard VGRBG-1116-0830SS Rear Bumper Guard Project
The portrait full film and assessment remain above on this video page. The project diary keeps the full landscape film and all three stage clips with the assembly account.